Page 1 of 2

am i not pleased

Posted: Mon Jun 15, 2009 8:27 am
by fastasfcuk
out on the loved one yesterday round carsinton water my mirrors would'nt keep still and were no good for seeing if plod was behind me.so we pulled over,mirrors were tight there was a slight lift in the nose fairing,but everthing looked ok.on the way home they were really bothering me. got home and on a really close inspection i spotted two strips of shiny metal where the clock mounting bracket bolts to the yoke.it had cracked both sides so i don't know what else is holding the nose fairing on.i'll be ringing two wheels today as this was replaced at the end of last year when brittany ferries dropped it.

did they fit a new one,or just straighten mine.

Posted: Mon Jun 15, 2009 9:14 am
by jayboy
My mirrors also vibrate quite a bit, and at a ton, the whole nose fairing shakes aswell, which I thought excessive.

I know the bike was dropped as there is a scrape on the right hand edge nearest the clip on.

Posted: Mon Jun 15, 2009 9:47 am
by Nooj
Not the first time I've read of this happening. It's by no means a common thing, but other owners have seen it, could be something that only happens to dropped bikes? Usual practice I believe is to weld it back up and add a couple of bracing triangles there to add some strength.

Posted: Mon Jun 15, 2009 2:06 pm
by Falcomille
Sounds like they straightened it up and cracked the welds, as these buggers are about £175 or so each. I would be knocking on their door....
Good luck

Posted: Mon Jun 15, 2009 3:48 pm
by fastasfcuk
jayboy wrote:My mirrors also vibrate quite a bit, and at a ton, the whole nose fairing shakes aswell, which I thought excessive.

I know the bike was dropped as there is a scrape on the right hand edge nearest the clip on.
i'd give it a really close inspection as my nose fairing and mirrors were solid before this started.mine was dropped on the right side and it bent the bracket,
and i had heard if you try and straighten them they do crack.my invoice was for a new bracket along with other items so i will be asking them if they did put a new one on.spoke to them this afters and i'l be taking the bike in tomorrow, if it's faulty they'll replace it,
but he knew what i was on about before i'd finished explaining. i think they've tried to pull a fast one.

Posted: Tue Jun 23, 2009 3:21 pm
by fastasfcuk
now i'm really mad, :smt010 took the bike in today to check out the cracked front frame and was shown an invoice for the replacement so no gripe there then. then the machanic advised me not to ride the bike home as he thaught it was dangerous with nothing holding the front on.even better, (you know) ca'nt get one for 8 weeks plus.so looks like i'm stripping the front off and welding the bracket untill the new one arrives.

Posted: Tue Jun 23, 2009 9:41 pm
by sabestian
Well, if they let you keep the old one (and you repair it), you'll have a spare new one waiting just in case! One of the rarest and/or dearest parts!

Posted: Tue Jun 23, 2009 10:07 pm
by HowardQ
I reckon the temp. fix should see you sorted and back on the road OK Ian. Bloody hope so, eight weeks is a long time for a English summer and the nights are already drawing in!
Hope you're back on the road soon mate.
Remember the old Carol King song, "It might as well rain until September", that's about where eight weeks takes you. :smt009

Posted: Tue Jun 23, 2009 10:30 pm
by Falcopops
HowardQ wrote:Remember the old Carol King song, "It might as well rain until September"
Damn Howard, now you're really showing your age :smt002

Posted: Wed Jun 24, 2009 2:53 pm
by HowardQ
If you've got it flaunt it so they say!
(Age that is!)
One of my earlier albums!

Posted: Wed Jun 24, 2009 5:16 pm
by fastasfcuk
ImageImageImageImageImagework on going, ca'nt weld it it's alloy.

Posted: Wed Jun 24, 2009 7:19 pm
by D-Rider
Cut a piece of steel plate and rivet the broken sides to it?

Nice clean break though!

Posted: Wed Jun 24, 2009 8:25 pm
by mangocrazy
I'm no metallurgist, but that break looks as though it was waiting to happen for a long time. To me it points to a manufacturing defect, almost as if the machine which bent the metal through a right angle to form the bracket had either partially cut through the metal or initiated a stress fracture.

That doesn't look 'normal' at all. Having said that, I should imagine it would weld up OK, especially if you removed what's left of the bracket from the steering head and welded it up in the interior angle.

Posted: Wed Jun 24, 2009 9:00 pm
by fastasfcuk
probably right,but i ca'nt mig it as i'm sure it's alloy a magnet dos'nt take to it.i know a firm close by who do cast and alloy just to get me by. my original bracket was fine untill it got bent. unless this one is after market.
duno.

Posted: Sat Jul 04, 2009 8:03 pm
by wavey
Fastasfcuk you have PM