RiderSite.com - Motorcycle Forums

Posted: **Mon Jun 25, 2007 8:14 am**

Further to my post in another thread, these are what I'm looking for, can anyone help please

I know they might look okay to you in the pictures but they aren't, millions of cracks in them and the scrapes looked as if they were made from rope, all hairy.

Posted: **Mon Jun 25, 2007 10:01 am**

Would they seriously not repair at a plastic welders or something? Can't really tell from the photos admittedly.

Fancy floggin them on anyway? I know of a bike that could use them for a little project!

Posted: **Mon Jun 25, 2007 10:39 am**

Sorry Bigun, they've been binned now and I seriously doubt they'd be any good because of the cracks.

Posted: **Mon Jun 25, 2007 11:51 am**

Binned ! The rareity of falco panels and you chucked better ones than i have on my bike.

Posted: **Mon Jun 25, 2007 1:07 pm**

Gio - I think I've the top two. In fact, I think I've got two of each (along with most other panels / fuel tanks) except for the upper fairing...

I'll check them out tonight. The only concern I think is that the side panel may have been drilled for an R&G upper crash bung.

Posted: **Mon Jun 25, 2007 3:03 pm**

TreeTops wrote:Gio - I think I've the top two. In fact, I think I've got two of each (along with most other panels / fuel tanks) except for the upper fairing...

I'll check them out tonight. The only concern I think is that the side panel may have been drilled for an R&G upper crash bung.

Drilled out is no problem TT. I can fill them myself

Posted: **Mon Jun 25, 2007 6:35 pm**

YOU DID WHAT!! Feksakes Gio! They'd have paid for loads of the bits you needed! Gold plated Hen's teeth they are!

Ah well.

Posted: **Mon Jun 25, 2007 7:07 pm**

Kwackerz wrote:

YOU DID WHAT!! Feksakes Gio! They'd have paid for loads of the bits you needed! Gold plated Hen's teeth they are!

Ah well.

Well I'll bow to you superior knowledge..........................................

NOT

I'd really liked to have shown pictures that show the damage, but as I only have one pair of hands that was impossible.

The rear of each panel was a veritable crazy pavement.

I've also been told that Aprilia are using a form of plastic composite that doesn't encourage repairs.

Posted: **Mon Jun 25, 2007 7:31 pm**

They'd have sold like hotcakes!

Bet theyre on Ebay now.. some binman is laughing at his good fortune.

Repair resistant composite? I seem to recall seeing plenty of Aprilia plastics being repaired (not just the race fairings) in '04

Posted: **Mon Jun 25, 2007 7:54 pm**

Kwackerz wrote:They'd have sold like hotcakes!

Bet theyre on Ebay now.. some binman is laughing at his good fortune.

Very unlikely, I'm pleased to say

Posted: **Tue Jun 26, 2007 6:12 pm**

Still need levers?

Posted: **Tue Jun 26, 2007 8:53 pm**

Nooj wrote:Still need levers?

Yes please

Posted: **Tue Jun 26, 2007 9:29 pm**

Ah, replied to your other post but it all went quiet. £15 for both the levers and adjusty bits and they're yours.

Posted: **Wed Jun 27, 2007 8:39 am**

If he doesnt want them, i'll have them. Need a brake lever and right clipon to replace bent items but i'd prefer a pair of both to build up me spares

Posted: **Wed Jun 27, 2007 8:57 am**

Nooj wrote:Ah, replied to your other post but it all went quiet. £15 for both the levers and adjusty bits and they're yours.

Done.

Pm me your addy or however you prefer to receive your funds and I'll sort it out today

RiderSite.com - Motorcycle Forums

Falco panels wanted

Falco panels wanted