Fork rebuild
Moderators: Aladinsaneuk, MartDude, D-Rider, Moderators
Fork rebuild
In the next week I'm finally going to strip my forks, fit the Race-Tech gold valves that have been sitting in the garage for two years and some progressive springs.
Unless something else comes up like it has every other time.
Fingers crossed
Unless something else comes up like it has every other time.
Fingers crossed
- mangocrazy
- Admin
- Posts: 3910
- Joined: Thu Jul 17, 2008 3:24 pm
- Location: Sheffield, UK
Re: Fork rebuild
Good luck! I fitted RT Gold compression valves and they made a big improvement to front end feel and operation. Do you have both compression and rebound valves or just compression? The difference in porting between standard Showa and the RT Gold valves is very noticeable.
I take it you've got a tool to compress the fork spring so you can get at the nut that needs to be unscrewed to remove the fork cap? When stripping the cartridge unit, be careful to clean up the part on the screw where it's been staked before undoing the nut. It's fiddly but needs doing to avoid damage. Once you've undone the nut I tend to get a thin cable tie and insert that through the centre of all the cartridge components as you withdraw the screw/bolt and then tie it off. That way all the components are kept in the correct order and orientation.
I take it you've got a tool to compress the fork spring so you can get at the nut that needs to be unscrewed to remove the fork cap? When stripping the cartridge unit, be careful to clean up the part on the screw where it's been staked before undoing the nut. It's fiddly but needs doing to avoid damage. Once you've undone the nut I tend to get a thin cable tie and insert that through the centre of all the cartridge components as you withdraw the screw/bolt and then tie it off. That way all the components are kept in the correct order and orientation.
Re: Fork rebuild
Thanks but it's no bother, I've done a lot of forks over the years.
- mangocrazy
- Admin
- Posts: 3910
- Joined: Thu Jul 17, 2008 3:24 pm
- Location: Sheffield, UK
Re: Fork rebuild
No probs - didn't know your skill level.
Re: Fork rebuild
I liked the write-up you did with your LC forks, I'm thinking about doing the same.
- mangocrazy
- Admin
- Posts: 3910
- Joined: Thu Jul 17, 2008 3:24 pm
- Location: Sheffield, UK
Re: Fork rebuild
I can recommend it. I was impressed when I rode the bike for the first time - suspension felt responsive and a lot better than I remembered it. I also fitted a replacement YSS shock and once that had 'run in' for a hundred miles or so felt similarly good. It will never be Ohlins standard, but feels a lot more 'modern'.
Re: Fork rebuild
Finally got the forks rebuilt a few months ago and it's transformed the front end, well worth doing.
Unfortunately I'm having bother with my wrist so I'm looking at a top yoke conversion or another bike. Bloody typical when I've just got it sorted.
Unfortunately I'm having bother with my wrist so I'm looking at a top yoke conversion or another bike. Bloody typical when I've just got it sorted.
- mangocrazy
- Admin
- Posts: 3910
- Joined: Thu Jul 17, 2008 3:24 pm
- Location: Sheffield, UK
Re: Fork rebuild
That really would be a shame. I'd persist with the Falco now you've got it how you want it (apart from bar position). I'm in very much the same position. The last ride I went on made me realise that the bar position is too low for comfort on my ageing bones, but the bike has had front forks and shock overhauled and is feeling better than ever.
I've already modified the bars by using a bar mounting clamp on top of the yoke (forks pushed through the top yoke by 6 rings to make space) and modified bars fitted), but I need to go further with that plan. I don't really want a top yoke conversion if I can avoid it. So I've bought a pair of these only to discover I already had a pair:
https://www.aliexpress.com/item/32970646020.html
These give a 30mm rise and if I use them in conjunction with a set of bars shaped like those below that should move the bar position up and back enough to take a lot of weight off my wrists.
Actual dimensions may change, but that is the general idea of what I have planned. I already use bars of that type in conjunction with clamps that don't give the 30mm rise, but the offset is only about 45mm at most. Using clamps with a higher start position and significantly more offset on the bars should make it easier on my wrists. That's the plan, anyway.
I've already modified the bars by using a bar mounting clamp on top of the yoke (forks pushed through the top yoke by 6 rings to make space) and modified bars fitted), but I need to go further with that plan. I don't really want a top yoke conversion if I can avoid it. So I've bought a pair of these only to discover I already had a pair:
https://www.aliexpress.com/item/32970646020.html
These give a 30mm rise and if I use them in conjunction with a set of bars shaped like those below that should move the bar position up and back enough to take a lot of weight off my wrists.
Actual dimensions may change, but that is the general idea of what I have planned. I already use bars of that type in conjunction with clamps that don't give the 30mm rise, but the offset is only about 45mm at most. Using clamps with a higher start position and significantly more offset on the bars should make it easier on my wrists. That's the plan, anyway.
Re: Fork rebuild
Sounds like a plan, good luck with it!
Don't know if I can be ars*d with the trouble. I'm looking at a top yoke conversion but if that means I have to cut the fairing it's getting sold and I'll get something else.
What to get is another matter..
Don't know if I can be ars*d with the trouble. I'm looking at a top yoke conversion but if that means I have to cut the fairing it's getting sold and I'll get something else.
What to get is another matter..
- mangocrazy
- Admin
- Posts: 3910
- Joined: Thu Jul 17, 2008 3:24 pm
- Location: Sheffield, UK
Re: Fork rebuild
I have no intention of cutting any of my fairing parts. I will be acquiring a top fairing that's suffered crash damage and which needs repairing, and if any cutting is required, that will be the parts that suffers. However I intend to avoid that if at all possible. I'll also get the new bars fabricated with a longer 'short' arm if you see what I mean , so I have the option of moving the whole bar assembly inboard to some degree if needed.
This would also reduce overall bar width and make it easier to get down the passageway in the row of terraced houses that we live in. Can take photos if the idea might be of use...?
An obvious alternative would be an Aprilia Tuono, I guess. You have V2 or V4 options...
This would also reduce overall bar width and make it easier to get down the passageway in the row of terraced houses that we live in. Can take photos if the idea might be of use...?
An obvious alternative would be an Aprilia Tuono, I guess. You have V2 or V4 options...
- katie1
- Clubman Racer
- Posts: 299
- Joined: Sun Oct 16, 2016 9:08 am
- Location: Oxfordshire
- Main bike: S1000RR, 1290 SDGT
Re: Fork rebuild
Or a Super Duke R?
Remember, when you are dead, you do not know you are dead. It is only painful for others.
The same applies when you are stupid.
The same applies when you are stupid.
- mangocrazy
- Admin
- Posts: 3910
- Joined: Thu Jul 17, 2008 3:24 pm
- Location: Sheffield, UK
Re: Fork rebuild
Have to cut the fairing so looks like the Falco's going.
Probably looking at getting a Tuono.
Probably looking at getting a Tuono.
Re: Fork rebuild
Will be looking for a Gen1 Tuono when I get home in a couple of weeks. Decision made!
Much as I love my Falco I need an improved riding position to take the weight off my wrists and don't want to have to chop the fairing.
I'll be putting a for-sale ad in classifieds on here first in case any future enthusiasts are looking before throwing it on ebay.
Thanks for all the help and advice over the past few years, this has to be one of the most helpful and pleasant bike forums I've had the pleasure to be part of.
(LC forum are great too if anyone's thinking about pulling their hair out for a couple of years doing a full resto!).
Davey.
Much as I love my Falco I need an improved riding position to take the weight off my wrists and don't want to have to chop the fairing.
I'll be putting a for-sale ad in classifieds on here first in case any future enthusiasts are looking before throwing it on ebay.
Thanks for all the help and advice over the past few years, this has to be one of the most helpful and pleasant bike forums I've had the pleasure to be part of.
(LC forum are great too if anyone's thinking about pulling their hair out for a couple of years doing a full resto!).
Davey.
-
- Despatch Rider
- Posts: 70
- Joined: Mon Jan 20, 2020 4:00 pm
Re: Fork rebuild
No need to chop the fairing if you move the bars over the yokes. Raises them 45mm. Not as comfortable as flat bars, unless you're getting a wriggle on but way better than stock.